Canon BCI-3, BCI-3e, BCI-6

Black & Color Cartridges

1. Cover the outlet hole(s) with Aluminum or Vinyl Tape to prevent ink loss during refilling.

2. Use the Thumb Drill provided to drill a 1/16' hole in the top of the tank. There is a recess in front of the Plastic Ball Bearing that is an ideal spot to drill through.

3. Attach the needle to the syringe and fill with the correct color ink.

4. Slowly inject approximately 4 ml. of ink into the filling hole until the chamber is almost full. Unused ink may be returned to the bottle.

5. Seal the hole using the set screw ( the set screw will self-tap and form an excellent plug which can be removed and re-installed each time you refill). Screw in the set set screw until it is flush with the top of the cartridge.Some ink will leak from the print head.

6. Remove the tape from the outlet hole(s).

7. Set above a paper towel for an hour as a drip precaution. Expect a few drips until the vacuum stabilizes.If it looks like the dripping doesn't stop, then the filling hole has an air leak and is not sealed well.

8. After the dripping has stopped, replace the cartridge and run 1 - 3 cleaning cycles as per printer instructions.

Canon BCI-3e, BCI-6

Refill Instructions Canon BCI-3e, BCI-6


Black & Color Cartridges

1. Cover the outlet hole with the orange outlet seal that came with the cartridge (a rubber band will hold this in place) or with your finger over the outlet port while wearing latex gloves or with some vinyl tape to prevent ink loss during refilling.

2. Use the "L tool" provided to push the Sealing Ball into the cartridge (tap on the 'L tool' if the ball is stuck). If you can't see the ball just above the "push" then peel back the top label on the reservoir side of the cartridge to expose the Sealing Ball. This is the ball Canon used to plug up the hole after they refilled the cartridge. (As an alternative you can drill a small hole into the reservoir side.)

3. Attach the needle to the syringe and fill with the correct color ink.



4. Slowly inject approximately 13 ml. of Black Ink or 6 ml of Color Ink slowly into the filling hole until the chamber is almost full. Unused ink may be returned to the bottle.

5. Seal the hole using the Green Plug. Put your finger on the green plug and twist until it is seated well in the hole. If you drilled a small hole then seal it with a drop of hot glue. This hole must be sealed air tight or all your ink will drip out.


6. Remove the orange outlet seal (or your finger, or the vinyl tape) from the outlet hole.

7. Replace the cartridge and run 1 - 3 cleaning cycles as per printer instructions.

8. If you have trouble getting your cartridge to print and the sponge side of the cartridge looks dry then drill a hole (or burn a hole with a hot paper clip) into the top of the sponge side of the cartridge. Stick the syringe needle into the sponge and fill with ink. You do not need to seal this hole.

CANON BCI-21/24 -COLOR

CANON BCI-21/24 -COLOR

Includes printers: Canon BJC-4000, BJC-4100, BJC-4200, BJC-4300, BJC-4550 and Apple StyleWriter 2400

MODIFY THE CARTRIDGE

The cap on the top of the cartridge must be removed. Hold the cartridge with the label facing you. Insert the blade of the knife where the cap meets the cartridge and twist. The cap should pop off very easily. You can also grab the cap with pliers and crack it off. Be careful not to break the finger on the back of the cartridge. This finger holds the cartridge into the print head. The cap is not need anymore.

IDENTIFYING THE VENT HOLE

Once the cap is off your will see 6 holes. The 3 larger holes are not fill holes. The smaller holes are the fill holes. In order to inject the ink you must first drill out the fill holes. Using the thumb drill provided, drill into each small hole until you feel the drill go through the plastic. Optionally you may put a piece of tape over the outlet hole to prevent the cartridge from dripping while refilling. You are now ready to inject the ink.

INJECTING THE INK

Tape over the two holes which you AREN'T filling to prevent ink contamination or have the hole you are filling slightly angled down in case you over fill the ink will run away from the other two holes. Each color can only take about 3 cc when empty, so don't expect much. Insert the needle all the way into the cartridge deep into the hard sponge. Inject S-L-O-W-L-Y to fill the entire cartridge. Be sure to remove and re-insert the needle a few times to expose the entire sponge to the ink.

Set on a paper towel for an hour as a drip precaution. Expect a few drips. Cover all holes during storage to prevent leaks and evaporation.

Replace the cartridge and run 1 - 3 cleaning cycles as per printer instructions.

Canon BCI-15 and BCI-16

Theory
The ink in these cartridges are retained because the cartridges have an internal sponge.

Instructions

Step 1) Put the cartridges on some paper towels in an area where you can tolerate a spill.

Step 2) Turn the cartridge up side down so that the outlet port of the cartridge is facing upward.

Step 3) For Black - Fill the syringe with 3cc of black ink.For Color - Fill a syringe with 2cc of cyan ink, another syringe with 2cc of magenta ink and a third syringe with 2cc of yellow ink.

Step 4) Drip ink onto the felt pad in the outlet port. The felt pad will quickly absorb the ink into the cartridge. If the felt pad will not soak up any more ink and the ink just sits on top then that chamber is full. Dab a paper towel onto the felt pad to soak up any ink that did not get absorbed into the cartridge. It goes without saying that you want to put the correct color into the correct chamber. Don't drip yellow ink onto the cyan felt pad and wonder why you are now getting green.Note: Do not pierce the felt pad the the needle of the syringe.

Step 5) Replace the cartridge and run 1 - 3 cleaning cycles as per printer instructions.

CANON BCI-10 & BCI-11

CANON BCI-10 & BCI-11
Also Apple M3912GA, and M3910GA Cartridges.
Canon BJC 30 and BJC 70 Series Printers
as well as Apple Stylewriter 2200 Portable Printers.

1. Peel back the label to reveal the vent holes.
2. Insert the syringe through the vent hole, and push into the center of the cartridge. The cartridge contains sponge and a slight resistance will be felt.
3. Slowly inject up to 5ml. of ink for black ink or 3 ml. of color ink for each color or until ink appears at the filling hole.

OR

1. Flip over the cartridge. Locate the sponge(s) on the bottom.
2. Inject the cartridge with about 2 cc of ink Be careful -- this sponge doesn't hold much ink!
Inject S-L-O-W-L-Y to fill the entire cartridge. Be sure to remove and re-insert the needle a few times to expose the entire sponge to the ink.

Note - Set on a paper towel for an hour as a drip precaution. Expect a few drips. Cover all holes during storage to prevent leaks and evaporation.

Unused ink may be returned to the bottle.

Replace the cartridge and run a priming cycle as per printer instructions.

Canon 7000 series printers

Theory

The ink in these cartridges is retained because the cartridge has an internal sponge.

Special Caution

The clear WJ811 fluid (print enhancer fluid) is particularly tricky to work with. If
this fluid contacts the ink, the ink will instantly dry and be nearly impossible to
remove.

Canon uses this fluid to create a quick-dry effect when printing on non-coated plain
paper. Unfortunately, if a drop of this fluid gets on a printhead which contains ink (or
vice versa), the material instantly forms a substance similar to acrylic in texture.

Use extreme caution handling this fluid near your printer and in handling inks
near this fluid. Otherwise, you will find yourself with a clogged printhead!

A few other comments

1. Our chemist ran tests using the original Canon cartridges with the original ink. He ran
   tests with over a dozen cartridges. In all cases, running full pages of black print, there
   were present white lines, streaks, and density variations when the print enhancing fluid
   was used. During this test, the black ink cartridge averaged 45 pages while the enhancing
   fluid lasted 105 pages on average.


2. The black chamber and the clear chamber both have air detecting tubes which are used to
   sense when the chamber is empty. When refilling, occasionally there will be air bubbles
   remaining in these tubes after refilling, so there will seem to be enough ink, but the
   printer will beep that you are out of ink.

   We recommend never running these cartridges
   dry. Your refilling will be much better if you refill whenever you get to about a quarter
   of the cartridge remaining.

   
   


3. If the clear chamber goes dry, it is almost impossible to refill successfully. Luckily,
   the clear chamber typically outlasts the black chamber by a ratio of 2:1, so we recommend
   topping off the clear chamber with 5-7 cc of ink every time you refill
   the black chamber.


4. We ran a half dozen of the original Canon black cartridges out of ink and 4 of them
   experienced some permanent blockage of some of the print nozzles before running out of
   ink. This was during very heavy full page printing. We believe that this is due to
   overspray of the clear print enhancing fluid.

   We suggest that you not use the print
   enhancing fluid where possible. It is designed for use on plain paper -- as opposed to
   coated inkjet paper.

   
   


5. The clear fluid will react with most metals -- except stainless steel. It also reacts
   with many plastics. We suggest that you only use syringes which are made of stainless
   steel, polyethylene, or polypropylene. Our syringes are made of these materials. If you
   use another material, the fluid will form a cloudy mess that will eventually clog the
   printhead.


6. Now that we've frightened you, let us add that this material is similar to Calgon water
   softener. In other words, it is non-toxic but may cause eye irritation. Wash with plenty
   of water.

   It's not that bad to people, but this fluid is a pain to work with around
   ink. Canon put it in -- we provide it as a service.

   
   

Instructions

1. Seal the outlet hole(s) in the base of the cartridge
with tape.

2. Peel back label on top of cartridge enough to expose
the filling holes, as shown.  It will be the same on the black cartridge.

3. Enlarge the filling hole(s) in the top of the
cartridge(s) using a 1/16" hand drill.

4. Push needle all the way into the cartridge of the
appropriate color filling hole. Note: The cartridge contains sponge and a slight
resistance may be felt. Very slowly inject up to 10cc of black ink or 5 cc of color
ink into the sponge until the cartridge is full.

Remember the black cartridge also has a clear liquid that is filled on the opposite side
from the black.(Now, always top off the clear fluid with about
5-7 cc of WJ811 fluid. It is vital that this chamber not be allowed to go dry. Reread the
Special Caution above. Be sure not to get any clear fluid on the black exit hole.) When full, ink may seep from the filling and outlet holes.

5. Seal the filling holes(s) in the top of the cartridge
by reapplying the label.

6. Unused ink may be returned to the bottle. Clean the
syringe with water and dry for future use, or use with a different color ink.



7. Remove the adhesive tape on the outlet hole(s) and run 1 - 3 cleaning
cycles as per printer instructions.

BC-62 Photo Cartridge

The BC-62 photo cartridge has 6 ink wells.  The ink wells on the
front of the cartridge are the  normal inks.  The 3 ink wells on the back of the
cartridge are the photo inks.  Each ink well will hold up to 3cc of color ink.
 Fill according to the instructions above.

A Refill Kit should include Ink plus the following:

3 Syringes for color portion

3 Syringes for photo portion

2 Syringes (10cc) for black

Aluminum Tape

Thumb Drill

Canon BC-22e Photo Cartridge Canon BJC-2000/4200/4300/4400/4550/4650/5000

1. Remove plugs on top of cartridge with included eyelet screw.


2. Attach the needle to the syringe and fill with the appropriate color of ink.


3. To verify which color ink is in which chamber, insert a toothpick and check the color of the ink on the toothpick when it is withdrawn. Insert the syringe through the filling hole and push all the way into the cartridge. (Cover the other three holes with tape while filling one to prevent cross contamination)

Note: You may feel a slight pressure because the cartridge contains a sponge.


4. Slowly inject up to 10 ml. of ink, per chamber, then replace the original plugs on the
top of the cartridge.

(If they're too badly damaged, don't worry. The plugs are not necessary. You only need
cover the holes for extended storage or transportation to prevent leaking or drying out. )


5. Unused ink may be returned to the bottle. Rinse the
syringes with water and dry for future use.

6. Set on a paper towel for an hour as a drip precaution. Expect a few drips -- If
there aren't any drips, the sponge is not saturated and ready to print.

7. Replace the cartridge and run 1 - 3 cleaning cycles as per
printer instructions.

CANON BCI-21/24 / BC-232 BLACK

MODIFY THE CARTRIDGE

The cap on the top of the cartridge must be removed.  This can be accomplished very
easily with knife. (a dull knife) Hold the cartridge with the label facing you.
 Insert the blade of the knife where the cap meets the cartridge and twist. The cap
should pop off very easily.   Be careful not to break the finger on the back of the
cartridge.   This finger holds the cartridge into the print head.  Throw the
plastic cap out, it is not necessary to put it back on the cartridge.

IDENTIFYING THE VENT HOLE

Once the cap is off hold the cartridge so that it matches Diag. 1. The 3 larger holes are
not fill holes.  The small hole in the center of the cartridge is the fill hole. In
order to inject the ink you must first drill out the fill hole.  To enlarge the fill
hole, drill until you feel the drill go through the other side. Optionally you may put a
piece of tape over the outlet hole to prevent the cartridge from dripping while refilling.
   You are now ready to inject the ink.

INJECTING THE INK

Inject the cartridge with about 4 cc of ink. Insert the needle all the way into the
cartridge deep into the hard sponge.

Inject S-L-O-W-L-Y to fill the entire cartridge. Be sure to remove and re-insert the
needle a few times to expose the entire sponge to the ink.

Set on a paper towel for an hour as a drip precaution. Expect a few drips. Cover all holes
during storage to prevent leaks and evaporation.

Replace the cartridge and run 1 - 3 cleaning cycles as per printer
instructions.

Canon BC-20/23 (Also includes: Canon BJC-4000, BJC-4100, BJC-4200, BJC-4550, BJC-5000)

Refilling the BC-20/23 Cartridge

1. For the Black BC-20 or BC-23 Cartridge, locate the round circle on top
   of the cartridge. There is a small hole off-center inside this round circle.


2. Use a 1/16 inch Thumb drill provided enlarge this small hole on top of the cartridge.
   (This may be covered by a label.) Drill completely through the plastic into the sponge.


3. Inject the Black BC-20/23 cartridge with about 30 cc of ink -- a full syringe. Insert
   the needle all the way into the cartridge deep into the hard sponge.


4. Inject S-L-O-W-L-Y to fill the entire cartridge. Be sure to remove and re-insert the
   needle a few times to expose the entire sponge to the ink.


5. You only need cover the hole with a piece of aluminum tape for extended storage or
   transportation to prevent leaking or drying out. Remove the tape when printing.



6. Set on a paper towel for an hour as a drip precaution. Expect a few drips. Cover all
   holes during storage to prevent leaks and evaporation.


7. Replace the cartridge and run 1 - 3 cleaning cycles as per printer
   instructions.
   

Canon: BCI-10 & BCI-11 (Also Apple M3912GA, and M3910GA Cartridges.)

Canon BJC 30 and BJC 70 Series Printers
as well as Apple Stylewriter 2200 Portable Printers.

1. Peel back the label to reveal the vent holes.

2. Insert the syringe through the vent hole, and push into the center of the cartridge. The cartridge contains sponge and a slight resistance will be felt.

3. Slowly inject up to 5ml. of ink for black ink or 3 ml. of color ink for each color or until ink appears at the filling hole.

OR

1 Flip over the cartridge. Locate the sponge(s) on the bottom.

2 Inject the cartridge with about 2 cc of ink Be careful -- this sponge doesn't hold much ink!
Inject S-L-O-W-L-Y to fill the entire cartridge. Be sure to remove and re-insert the needle a few times to expose the entire sponge to the ink.

Note - Set on a paper towel for an hour as a drip precaution. Expect a few drips. Cover all holes during storage to prevent leaks and evaporation.
Unused ink may be returned to the bottle.

Replace the cartridge and run a priming cycle as per printer instructions.

Canon: BC-05 BC-06 Photo Cartridge (Also Apple M8052GA, M8041GA, and M4609GA Cartridges.)

Many different Canon and Apple Stylewriter Printers

Theory
The ink in this cartridge is retained because the cartridge has an internal sponge.

Instructions
Step 1) Put the cartridge on some paper towels in an area where you can tolerate a spill.

Step 2) Locate the three vent holes on the longest side of the cartridge at the opposite end from the print head. Each hole leads to a seperate color chamber.

Step 3) Use the thumb drill provided to open up these vent holes, using them as starter holes. Drill just through the plastic top.

Step 4) Insert a toothpick or unbent paper clip into the holes to verify the color of the ink in each of the three color chambers -- yellow, magenta, cyan

Step 5) Tape over the two holes you aren't currently filling to avoid accidental contamination with the wrong color of ink.

Step 6) Using the syringe draw 2cc of ink from the plastic bottle. Insert the needle fully through the hole.

Step 7) S-L-O-W-L-Y inject the ink into the sponge.

Step 8) Recognize that each color is not used equally, and therefore, only one color will take the full 2cc.

Step 9) Remove all tape and set above a paper towel for an hour as a drip precaution. Don't allow the printhead to touch the paper towel or all of the ink will be drawn out. Expect a few drips -- If it doesn't drip, the ink is not ready to print. It is not necessary to seal the holes except during long storage and transportation.

Step 10) Replace the cartridge and run 1 - 3 cleaning cycles as per printer instructions.

Canon: BC-01, BC-02 (Also Apple M8052GA, M8041GA, and M4609GA Cartridges.)

Many different Canon and Apple Stylewriter Printers
There are two different types of these cartridges. The older type has a single vent hole and the newer type has two vent holes.

DOUBLE HOLE MODEL
Locate the refill plug (top right of the cartridge). Using the eyelet screw provided twist it into the vent hole 3 or 4 times and pull the plug out. You are now ready to refill the cartridge. Place the cartridge on several layers of newspapers. Inject up to 20cc of black ink into the cartridge. Pause occasionally and let the sponge soak up the ink. The cartridge may not take all the ink since it may not be totally empty.

SINGLE HOLE MODEL
Locate the refill plug (top right of the cartridge) . Enlarge the vent hole using the 1/16" thumb drill provided. Place the cartridge on several layers of newspapers. Inject up to 20cc of black ink into the cartridge. Pause occasionally and let the sponge soak up the ink. The cartridge may not take all the ink since it may not be totally empty.

Set on a paper towel for an hour as a drip precaution. Don't allow the printhead to touch the paper towel or all of the ink will be drawn out. Expect a few drips -- If it doesn't drip, the ink is not ready to print. It is not necessary to seal the hole except during long storage and transportation.

Replace the cartridge and run 1 - 3 cleaning cycles as per printer instructions.

Brother: LC51

1) Cut label at joint between top and bottom halves of
the cartridge case.

2) Flip open the cartridge casing (shell).

3) Put the sharp filling needle onto the syringe and fill the
syringe with ink.

4) Pierce the top part of the cartridge with the needle and S-l-o-w-l-y
inject 15 cc of ink into the cartridge bag.

5) Put a piece of aluminum tape over the filling hole.

6) Place the casing(shell) back together and use a piece of tape to hold the two sides of the casing(shell) together.

Note: Do not bump or press the "pressure release button".

7) Replace the cartridge(s) and run 1 - 3 cleaning cycles
as per printer instructions.

Brother: LC41

There are two methods you can use to refill this cartridge.

Use the one that suits you the best.

Method One

1) Put the needle onto the syringe and suck up 25 ml
of black or 20ml of color ink.

2) Remove the needle from the syringe.

3) Put the cartridge on a flat, ink proof
surface, with the bottom facing up.

4) Push the tip of the syringe into the "ink exit hole" and tilt the
syringe to the side. Remember, you should not have the needle on the
syringe.

Note: Do not bump or press the "pressure release button".

5) Pull back on the syringe plunger until
3-4 ml of air from the cartridge bubbles up through the ink. A slight vacuum
will form in the cartridge. Then push on the syringe plunger slightly to
inject 3-4 ml of ink.

6) Repeat this step 5-8 times to pump the
air out of the cartridge and replace it with ink

7) When the process is complete, the
syringe will be filled with air. Pull back on the syringe plunger one more
time to pull a few extra ml of air out of the cartridge and then pull the syringe
out of the "ink exit hole".

8)Replace the cartridge(s) and run 1 - 3 cleaning cycles
as per printer instructions.

---

Method Two

1) Put the cartridge on a newspaper or some paper towels in an area where
you can tolerate a spill.

2) Turn the cartridge on its side and drill a hole 1/4 inch down from the black cap into
the clear part of the plastic (see Photo)

3) Fill the syringe with 20 ml. of ink.

4) Insert the syringe through the drilled hole, If the needle hits the inner part of
the cap then aim the needle in a downward position as seen in the photo.

5) Slowly inject ink
until you see the ink come up to just below the drilled hole.

6) Cut a small square of aluminum tape and reseal the drilled hole.

7) Unused ink may be returned to the bottle.  Rinse
the syringe with warm water and dry for future use.

8) Replace the cartridge(s) and run 1 - 3 cleaning cycles
as per printer instructions.

Brother: LC02, LC04, LC21, LC31, LC800

1. Remove cover by using a small flat blade
screwdriver and pry the tang holding the cover on the cartridge.

2. Remove the larger silver seal using a pocket knife or finger
nail.

3. Enlarge the filling hole in the top of the cartridge(s)
using the thumb drill provided.

4. Insert the syringe through the filling hole, and push all the way into the cartridge.  The cartridge contains a sponge and a slight resistance may be felt.

5. Slowly inject up to 7 ml. of ink

6. Reseal the filling hole/breather port with tape.

7. Replace the cover by snapping the cover back onto the cartridge.

8. Unused ink may be returned to the bottle.  Rinse
the syringe with warm water and dry for future use.

9.Replace the cartridge(s) and run 1 - 3 cleaning cycles
as per printer instructions.

Brother: LC02, LC04, LC21, LC31, LC800

1.Remove cartridge and put a piece of tape over the
outlet port to prevent ink drips during the filling process.

2. Pry off the black or color lid (cover) from the top of the
cartridge by using a small flat blade screwdriver.

3. Remove the larger silver seal using a pocket knife or finger
nail.

4. Enlarge the Filling hole in the top of the cartridge(s)
using the thumb drill provided.

5. Hold the cartridge so that the Vent hole (at the front of the
cartridge) is slightly higher than the Filling hole.

6. Insert the syringe through the Filling hole, and push all the way
into the cartridge.  The cartridge contains a sponge and a slight resistance may be
felt.

7. Very S-l-o-w-l-y inject up to 7 ml. of ink until the
reservoir under the Vent hole fills from the bottom to the top.

8.Reseal both holes (Filling and Vent) with tape.

9. Replace the cover by snapping the cover back onto the
cartridge.

10. Remove the tape from the outlet port when ready to
reuse the cartridge.

11. Unused ink may be returned to the bottle.  Rinse
the syringe with warm water and dry for future use.

12. Replace the cartridge(s) and run 1 - 3 cleaning cycles
as per printer instructions.

Brother: 5000/7000 Series

1. Cover the outlet hole with
a small piece of tape. If this is not done the ink may run out of the outlet hole
when the hole is drilled in the top of the cartridge.

2. Peel back label as shown in photo.

3. Using the thumb drill provided, drill into the recessed
area under the label until drill fully penetrates cartridge.

4. Fill syringe with 10 ml. of black ink. 5-8
cc of color ink for the color cartridge.

5. Very slowly inject the ink into the sponge until the
cartridge is full.

6. Seal the hole made in the top label with tape. Note: If
the holes are not sealed properly the cartridge will leak.

7. Unused ink may be returned to the bottle. Clean the
syringe with water and dry for future use, or use with a different colour ink.

8. Replace the cartridge and run 1 - 3 cleaning cycles as
per printer instructions.

Lexmark 10N0026

Z65 has a longer cartridge but refills the same

COLOR CARTRIDGE

1. The filler holes of the cartridge are located under the top. Remove the top before refilling by carefully prying it off with pocket knife.

2. It's a good move to check the color chambers with a toothpick before putting in ink. The chambers are somewhat dry and you might have to push the tooth pick in far to get ink on it.

3. Insert the filling needle
into the filler hole of the color to be refilled.




4.Slowly inject up to 3ml. of ink until the sponge is saturated.

Important: When you take off the color cartridge cap will notice that the sponge is white. Fill the individual colors until the color just begins to show in the white sponge.

5. After refilling the top can be put back on with scotch tape.

6. Replace the cartridge and run 1 - 3 cleaning cycles as per printer instructions.




For best results, leave cartridge in printer for 8 hours after refilling so the ink can saturate the entire sponge. (Allows ink to flow to the
print head).

HP #95 (C8766W) & #97 (C9363W) Color Cartridge

Instructions

1. Put the cartridge on some paper towels in an area where you can tolerate a spill.

2. Peal off the top label.

3. Fill the syringe with 6 ml. of color ink.

4. Very S-L-O-W-L-Y inject ink into each chamber until the
sponge full. A little ink might come out of the top when full, so cover up the other two holes while filling one.

5. When finished, replace the top label or leave it off (it will make no difference in the printing).

6. Replace the cartridge and run 1 - 3 cleaning cycles as per printer instructions.

For best results, leave cartridge in printer for 8 hours after refilling so the ink can saturate the entire sponge.

HP #94, #96, & #98 Black Cartridges

Instructions

1. Put the cartridge on some paper towels in an area where you can
tolerate a spill.

2. Peal off the top label.

3. Fill the syringe with
20 ml. of black ink.

4. Very S-L-O-W-L-Y inject ink into any hole (they all go
to the same sponge, HP just used the same color mold for the black ink cartridges).

5. When finished, replace the top label
or leave it off (it will make no difference in the printing).

6. Replace the cartridge and run 1 - 3 cleaning cycles as
per printer instructions.



For best results, leave cartridge in printer for 8 hours after refilling so the ink can saturate the entire sponge.